Driving compressor is needed: |
|
We have developed compressor booster which operates on the principle of an amplifier input pressure to the desired output pressure 300bar (4500PSI). For these reasons, for our booster operation need to be connected to source of low pressure air, which is most often compressor with low output pressure 6-10bar ie normal workshop compressor. If your low-pressure compressor is more powerful then our booster unit will work faster , resulting in faster performance of high-pressure air. |
|
|
Long life is assured by slow moving pressure cycle: |
|
Due to the large volume of pistons our compressor is working with significantly lower speed (up to 20x times lower sliding velocity) at the same or greater amount of compressed air supply than what similarly low-speed high-pressure compressors on the market have.Thanks to this slow piston movement and much smaller length movement is seal much less stressed than on higher movement speed. At the same pressure air supply pistons in our compressor travels 10-15x less distance than the high speed compressor, which also contributes to a further very long seal life. |
|
|
The self-cooling ensures low operating temperatures and continuous operation : |
|
The compressor booster has a built-in sophisticated cooling system of both cylinders using exhausted compressed air, which allows it to run uninterrupted, without causing excessive heating of the compressor.The surface temperature of the cylinders is approximately 40 ° C ( Max around 50 °C ). Low operating temperature also contributes to even longer seal life. |
|
|
Maintenance-free operation: |
|
On the basis of the properties described above and due to the fact that the our compressor booster does not need lubrication, the compressor operates without the need for ongoing maintenance. In our long-term testing (5 years of daily use), it was found that the compressor without any lubrication or seal replacement managed fulfill around 100 bottles with capacity 4liters of a pressure from 200 to 300bar than was necessary maintenance service. |
|
|
Compressor booster has automatic stop when required pressure in the bottle is reached: |
|
Compressor booster includes an adjustable pressure switch which stops the compressor after reaching the desired outlet pressure. Setting the desired output pressure can be easily performed in a range 60-300bar (900 to 4500 PSI). When compressor reaching the required pressure automatic stop switch itself . In the case of a pressure drop in the Airtank ( for example by cooling) automatic stop switch itself again refill airtank and then switch itself again to stop filling. |
|
|
The two-stage separator moisture and multiple filtration: |
|
Compressor basically contains cascade system moisture separator from the air, which provides very dry high pressure air output from the compressor. Thanks to this, it is not necessary to worry about the penetration of moisture into the bottles, or pressure container. At the same time inlet air is filtered several times to remove impurities. |
|
|
Easy seal replacement , spare seals set is included in compressor box : |
|
The compressor is designed for easy dismantling, so if is necessary to exchange any seal then overall time to exchange it should no take more than 15 minutes (the dismantling of the compressor – replacing seal – assembly compressor back). At the same time, most current seals on the compressor is already included in spare set supplied with the compressor. Specific seals can be ordered. |
|
|
High pressure hose with multifunction valve: |
|
Our compressor booster is ended with 0.75 meters long high pressure hose end with multifunctional valve with bursting disc on 500Bar (7500PSI), venting screw and female paintball coupling. Burst disc is functional protection in the event of over pressurization device and prevents damage to bottle. After unscrewing paintball coupling from multifunction valve is there present external thread on which it is possible to screw other pins or equipment. |
|
|
Low noise level: |
|
Compressor booster works quietly and in the case of storing blocks of foam rubber to blow-off holes can be achieved even more significantly quieter operation. |
|
|
Small size, light weight and practicality for carrying: |
|
Compressor is covered in box which has dimensions of 30x30x60 cm and a weight of slightly over 5 kg. With this low weight and convenient handles it can easily be transferred or transported. |
|
|
Protective outer box: |
|
The outer plastic transport box provides excellent protection for compressor equipment itself not only against mechanical damage, but also against the outside impurity. |
|
|
Medium pressure gauge for diagnosis : |
|
The output of the medium-pressure cylinder is ended with medium pressure gauge. This manometer can be used for controlling process and size of medium- pressure in system, which can be very useful for rapid diagnosis of compressor status and for finding specific defects. |
|
|
Setting air flow screw: |
|
Compressor includes tuning setting screw to reduce air flow from driving compressor This allows adjust steplessly speed of compressor booster and adjust air consumption for less powerful drive compressors so they can work in an effective pressure range. |
|
|
Warranty: 2 years |
|
Our compressors are supplied with 2 years warranty on mechanical parts or other defects. The guarantee does not apply to all seals. Details in the instruction. |